A-Plus Floor Guard® 100% Solids & Self-Levelling Epoxy Floor Coating

A-Plus Floor Guard® 100% Solids & Self-Levelling Epoxy Floor Coating is a 2-component premium epoxy floor coating ideal for the protection of indoor concrete floors in heavy-duty areas such as warehouses, laboratories, food processing plants, residential buildings, indoor parking areas, and many more. It is a 100% solids, self-levelling, heavy-duty epoxy floor coating that cures to a tough, smooth, and glossy finish that is capable of covering minor surface imperfections as well as exhibiting superior resistance against abrasion, impact, and chemical spillage such as oils, acids, and any more.

☑100% Solids, Superior Durability and Adhesion
☑Superior Resistance Against Abrasion, Impact, Spillage of Chemicals and Oils
☑Self-levelling, Penetrates Deep Into Pores
☑Completely Waterproof
☑Covers Minor Surface Imperfections
☑Low Maintenance, Easy to Clean Glossy Finish
☑1-Coat application, Save Time and Cost!

Category:

Specifications

Principal Uses: Applied on indoor concrete floors, heavy-duty areas such as warehouses, groceries, laboratories, food processing plants, kitchens, garage, parking areas, and many more.

Sheen: Gloss

Coverage: Sealer Coat: 25-30sqm per gallon

Topcoat: 8-10 sqm per gallon @ 400-600 micrometers thickness

Surface Dry: 3 – 4 hrs

Dry Through: Overnight curing time for light traffic, 3-7 days to achieve full strength

Thinning: Use as supplied.

Clean-up Solvent: Clean-up equipment or application tools with A-Plus® PG Epoxy Reducer while paint has not yet hardened.

Application: V-notched Trowel or V-notched Squeegee; Spiked Rollers (for releasing bubbles)

Packaging: 4L set

Mixing Ratio: 3:1 paint to hardener

Pot life: 30 mins – 1 hour

Compressive Strength(ASTM D695): 7000psi

Shelf Life: One year when stored in dry cool conditions

Colors: Available in 12 factory mixed colors

Surface Preparation & Precautions

General Instructions:

  1. Mixing ratio: 3:1 by volume, Paint and Hardener. Mix only enough paint for use in one session or paint job.
  2. WARNING! Pot life of mixed Paint and Hardener is around 1 hour at room temperature. Excess mixture that are not used up will gel within the day.
  3. Avoid painting under extreme environmental conditions and/or bad weather conditions.
  4. Do not put mixed components back into its original container.
  5. Clean up excess material with A-Plus® PG Epoxy Reducer while material has not cured.
  6. MIX WELL BEFORE USING.

For Concrete Flooring:

  1. Ensure proper surface preparation by removing any oil and dirt by detergent cleaning.
  2. Sand or use a mechanical floor grinder with large grit to roughen and level the surface, allowing the paint enhanced grip and adhesion.
  3. Rinse the concrete thoroughly with water to wash away residues that could affect paint adhesion. Allow ample time for the concrete surface to dry.
  4. To repair large concrete surface imperfections, use either of the following:

– A-Plus Procrete® Low Viscosity Construction Epoxy – used for patching medium-sized concrete imperfections covering a large area.
– A-Plus Procrete® High Viscosity Construction Epoxy – used for patching larger-sized concrete imperfections covering smaller areas.

For Metal Surfaces:

  1. Remove dust, dirt, grease, oil, wax and other foreign matter using a rag soaked in paint thinner.
  2. For repainting, use A-Plus Supertanggal® Paint Remover to strip off old paint film to bare substrate then remove oil and grease by detergent cleaning followed by scuff sanding. To remove rust, wire brush or strip affected areas after applying A-Plus® Rust Converter. Let it sit for 10 – 15 minutes before washing off surface thoroughly with water, letting it dry before applying paint.
  3. Primer should be applied immediately upon drying of the surface before rust sets in.

For Wooden Surfaces:

  1. Ensure proper surface preparation by removing any oil and dirt by scuff sanding.
  2. For repainting, use A-Plus Supertanggal® Paint Remover to strip off old paint film to bare substrate then remove oil and grease by detergent cleaning followed by scuff sanding.

Painting Procedure

Mixing Direction:

  1. Stir and shake both components separately before mixing together.
  2. Slowly add the hardener to the paint and mix slowly and thoroughly for 5-10 minutes before application.
  3. Mixing ratio is 3:1 paint to catalyst, respectively. For better mixing, transfer both components to a larger container.

Application Over Steel Floors:

  1. Apply 1 coat of A-Plus Floor Guard® Epoxy Floor Coating as topcoat using either a v-notched trowel or a v-notched squeegee. Tip: Pour a generous amount of the paint on the floor then spread evenly using the selected application tool.
  2. Use a spiked roller to remove any trapped air from the coating.
  3. Allow the surface to cure overnight before subjecting to light traffic. Allow the surface to cure for at least 3-7 days before subjecting to heavy traffic.

Application Over Concrete Floors (Plain Finish Without Aggregates):

  1. Apply 1 coat of A-Plus Floor Guard® Concrete Sealer using a short nap roller or paint brush. Allow to cure for at least 6 hours before the next step.
  2. Apply 1 coat of A-Plus Floor Guard® Epoxy Floor Coating as topcoat using either a v-notched trowel or a v-notched squeegee. Tip: Pour a generous amount of the paint on the floor then spread evenly using the selected application tool.
  3. Use a spiked roller to remove any trapped air from the coating.
  4. Allow the surface to cure overnight before subjecting to light traffic. Allow the surface to cure for at least 3-7 days before subjecting to heavy traffic.

Application Over Concrete Floors (Non-Skid Finish With Broadcast Aggregates):

  1. Apply 1 coat of A-Plus Floor Guard® Concrete Sealer using a short nap roller or paint brush. On the still wet A-Plus Floor Guard® Concrete Sealer, broadcast aggregates at 1kg per sqm. Allow to cure for at least 6 hours before the next step.
  2. Apply 1 coat of A-Plus Floor Guard® Epoxy Floor Coating as topcoat using either a v-notched trowel or a v-notched squeegee. Tip: Pour a generous amount of the paint on the floor then spread evenly using the selected application tool.
  3. Use a spiked roller to remove any trapped air from the coating.
  4. Allow the surface to cure overnight before subjecting to light traffic. Allow the surface to cure for at least 3-7 days before subjecting to heavy traffic.

Color Swatches

  • 9118

    ENDURO WHITE

  • 9122

    FACTORY BEIGE

  • 9142

    INDUSTRIAL RED

  • 9145

    VELVET RED

  • 9132

    STURDY ORANGE

  • 9125

    INDUSTRIAL YELLOW

  • 9155

    COOL GREEN

  • 9158

    CLASSIC GREEN

  • 9165

    COOL BLUE

  • 9168

    CLASSIC BLUE

  • 9185

    LIGHT GRAY

  • 9188

    MEDIUM GRAY

 

 

Related products

Quick View

Woodcraft and Varnishes

A-Plus PolySupreme® 2K Water-Based Heavy-Duty Polyurethane Floor Varnish

Quick View

Woodcraft and Varnishes

A-Plus PolyMega® 1K Water-Based Polyurethane Wood Varnish

Quick View

Floor Coatings

A-Plus Floor Shield® High-Build 2k Polyurethane Parking Floor Coating

Quick View

Floor Coatings

A-Plus Floor Master® Chlorinated Rubber Based Floor Coating

Quick View

Woodcraft and Varnishes

A-Plus PolyWood® Hi-Performance 2K Polyurethane Floor Varnish