A-Plus Paints | Paint Products Manufacturers and Suppliers in Philippines

A-Plus® Interior Enamel Semi-Gloss White is a solvent-based Alkyd Enamel paint suitable for a wide range of wooden and metal surfaces. It cures to a tough, durable, high build glossy coating with superior hiding power, resulting to a long-lasting beautiful finish. It is formulated for interior applications.

☑Premium Alkyd Enamel-Based Paint

☑Glossy and High Build Coating

☑Superior Durability and Adhesion

☑Excellent Resistance to Chemicals, and Oils

☑Protection Against Abrasion and Rusting

☑Easy to Use, Lead-Free

Category: Decorative Paints Tag: Alkyd Enamel / Oil Based Coatings

Specifications

Principal Uses: Wood and Metal Surfaces such as Window Trims, Furniture, Doors, Grills, and many more

Sheen: Semi-Gloss, High Gloss

Coverage: 25-30 sqm per gallon / coat, depending on surface porosity

Surface Dry: 4 – 5 hrs

Recoat Interval: 8 hrs

Dry Through: Curing time: 8 hours
Full cure within 3 days at room temperature and 50% relative humidity

Tinting: Can be tinted with A-Plus® Oil Wood Stains at a maximum level of 1/4L per 4L paint to achieve desired shade. Note that Hansa Yellow and Bulletin Red are for interior painting only.

Thinning: Maximum 1L A-Plus® PG Enamel Reducer per gallon paint

Clean-up Solvent: A-Plus® PG Enamel Reducer

Application: Brush/Roller/Spray

Packaging: 250ml, 1L, 4L, 16L

Surface Preparation & Precautions

For Wooden Surfaces:

1. Surface to be painted must be thoroughly cleaned, free of any contaminants.
2. Hammer nail holes and sand any surface defects with large grit sandpaper for better adhesion.
3. Repair cracks and other surface imperfections with A-Plus® Fast-Drying Plastic Wood Filler or A-Plus® Enamel Glazing Putty White.
4. Avoid painting under extreme environmental conditions and/or bad weather conditions.

For Metal Surfaces:

1. Remove dust, dirt, grease, oil, wax and other foreign matter using a rag soaked in paint thinner.
2. For new Galvanized Iron, wipe clean with paint thinner before sanding surface to enhance paint adhesion. For rusty metal surfaces, wire brush or strip affected areas after applying A-Plus® Rust Converter. Let it sit for 10 – 15 minutes before washing off surface thoroughly with water. Let dry before applying primer.
3. Apply a premium quality metal primer such as A-Plus® Metal Primer or Glazer Galva-Plus® Epoxy Primer immediately upon drying of the surface before rust sets in.

Precautions:

1. Surface to be painted must be thoroughly cleaned, free of any contaminants.
2. If previously painted, strip off all loose and chalking paint with A-Plus Supertanggal® Paint Remover.
3. Mix well before using.

Painting Procedure

Painting Procedure on Wooden Substrates:

1. If previously painted, strip off all loose and chalking paint using A-Plus Supertanggal® Paint Remover. Sand with large grit sandpaper to roughen surface.
2. Primer: Apply at least 2 coats of A-Plus® Flatwall Enamel White as primer.
3. Putty: Repair cracks and other surface imperfections with A-Plus® Fast-Drying Plastic Wood Filler or A-Plus® Enamel Glazing Putty White.
4.Topcoat: Apply 2-3 coats of A-Plus® Interior Enamel Semi-Gloss White. Allow at least 6-8 hours drying time between each coat.

Painting Procedure on Metal Substrates:

1. If previously painted, strip off all loose and chalking paint. If rust is present, apply A-Plus® Rust Converter first. Sand with large grit sandpaper to roughen surface.
2. Primer: Un-Galvanized or rusted metal substrates should be pre-painted with at least 2 coats of a premium quality anti-corrosive metal primer such as A-Plus® Metal Primer Red Oxide or Glazer Galva-Plus® Epoxy Primer.
3. Topcoat: Apply 2-3 coats of A-Plus® Interior Enamel Semi-Gloss White. Allow at least 6-8 hours drying time between each coat.

A-Plus® Interior Enamel Semi-Gloss White